ASTM A682 PDF


0
Categories : Education

ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

Author: Faugis Tautilar
Country: Bangladesh
Language: English (Spanish)
Genre: Software
Published (Last): 10 November 2011
Pages: 414
PDF File Size: 15.90 Mb
ePub File Size: 13.24 Mb
ISBN: 446-5-70142-483-8
Downloads: 91669
Price: Free* [*Free Regsitration Required]
Uploader: Zumi

Originally published as A — B The sum of copper, nickel, chromium, and molybdenum shall not exceed 0. C When edge, width and thickness are not de? When the amount of vanadium, columbium, or titanium is less than 0. Within the text, the SI units are shown in brackets. However, under SI the preferred term in mass. Revision to Table 2. The ability of manufacturers to meet the maximum coil weights depends upon individual mill equipment.

Within the text, the SI units are shown in brackets. When one or more of these elements is speci? NOTE 1—The term weight is used when inch-pound units are the standard.

ASTM A, AM_百度文库

Thickness Tolerances Plus or Minus, aastm. Last previous edition A — Conformance to SI tolerances is mandatory when the “M” specification is used. Link to Active This link will always route to the current Active version of the standard. Each of the elements listed in Tables 2 and 3 and additional elements agreed upon by the purchaser and the supplier shall be included in the report of heat analysis.

Over 12 Through 11? The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. However, unless the order specifies the applicable “M” specification designation SI unitsthe material ast be furnished to inch-pound units. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. When the amount of copper, nickel, chromium, or molybdenum is less than 0.

  GRISON TOCCATA PDF

Within the text, the SI units are shown in brackets. If any of the retests fail to comply with the requirements, the coil shall be rejected. When required, minimum coil weights are subject to negotiation.

However, under SI the preferred term in mass. Normal coiling or piling does not provide a 3 Where an ellipsis. Note 1—The term weight is used when inch-pound units are the standard.

The elements comprising the desired chemical composition are speci? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the context of the report. Strip is classified as product that is 0. Rejection and Rehearing Aa682 you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

The strip may be subjected to product analysis by the purchaser either for the purpose of verifying that the chemical composition is within speci?

ASTM A682 Grade 1074

The material must be adequately protected and correctly identi? However, unless the order speci? Conformance to SI tolerances is mandatory when the “M” specification is used. Table 3 shows requirements for additional elements. Government procurement by the Defense Supply Agency, strip material shall be continuously marked for identi?

  LTC 5136 PDF

Combining values from the two systems will result in nonconformance with the specification. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. B Measured 10 mm or more in from edge; and on narrower than 25 mm, at any place between edges. Elements such as aluminum may be added in sufficient amounts to control the austenitic grain size. For strip length under mm, camber tolerance shall be subject to negotiation.

NOTE 1—Camber is the greatest deviation of a side edge from a straight line, the measurement being taken on the concave side with a straight edge. Individual reprints single or multiple copies of this standard may be zstm by contacting ASTM at the above address or at phonefaxor service astm.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. A ast, in parentheses indicates the year of last reapproval. Unless otherwise agreed to, all tests and inspections, except product analysis, shall be made at the place of atsm. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

NOTE 2—The industry de?