ASTM D4066 PDF


0
Categories : Marketing

Buy ASTM D CLASSIFICATION SYSTEM FOR NYLON INJECTION AND EXTRUSION MATERIALS (PA) from SAI Global. ASTM D Standard Classification System for Nylon Injection and Extrusion Materials (PA). standard by ASTM International, 07/01/ View all product. 暂无评价|0人阅读|0次下载 | 举报文档. D – 01A Nylon Injection and Extrusion Materials_能源/化工_工程科技_专业资料。ASTM D标准.

Author: Jusho Vujind
Country: Ukraine
Language: English (Spanish)
Genre: Life
Published (Last): 2 July 2011
Pages: 456
PDF File Size: 8.16 Mb
ePub File Size: 6.18 Mb
ISBN: 491-7-43742-346-5
Downloads: 72071
Price: Free* [*Free Regsitration Required]
Uploader: Felkis

Active view current version of standard. The main property affected is ductility, as illustrated by a reduction in Izod impact and elongation values. Link to Active This link will always route to the current Active version of the standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

These are electrical limits applied to reinforced nylons when control of their electrical properties is required.

Industrial & Engineering Plastics

Tensile strength and elongation shall astj determined on Test Method D test specimens 3. Some of these compositions are also suitable for compression molding and application from solution. Plastic and Ebonite ISO A superscript epsilon e indicates an editorial change since the last revision or reapproval. F Flexural modulus shall be determined on Test Method D test specimens 3. Testing Conditions ISO Start the test within 2 min after removing the specimen and wiping with a dry cloth.

D ASTM International takes no position respecting the validity of any patent rights asserted in connection with asgm item mentioned in this standard.

J Carbon black content and absorbance must be 1. Relative viscosity of Group 08 shall be measured on 9. To be agreed upon between the user and the supplier.

  KATHY REICHS TESTIGOS DEL SILENCIO PDF

Flexural modulus shall be determined on Test Methods D test specimens 6.

ASTM D – 96 Standard Classification System for Nylon Injection and Extrusion Materials (PA)

The dissipation factor is the cotangent of the dielectric phase angle or the tangent of the dielectric loss angle. This example can be applied to replace all table values, that is, tensile stress, notched Izod impact, and heat de? The designation PA indicates the following: No moisture shall be intentionally added to reach this level. If no properties are speci?

Other 0 0 Other Other 0 0 No descriptions are listed unless needed to describe a special grade d4606 the class. Relative viscosities of Groups 03 and 04 shall be measured on 0.

This standard does not purport to address all of the safety concerns, if any, associated with its use. Material data for inje This standard has been approved for use by agencies of the Department of Defense. D Terminology Relating to Plastics. No descriptions astmm listed unless needed to describe a special grade under the class.

Last previous edition D — Historical Version s – view previous versions of standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. All other grades are listed by requirements. NOTE 11—Pigmented or colored nylons can differ signi? The melting point, Tm, is obtained from the second melting curve. Selection of process temperature is made based on the major polymer component. The report shall consist of results d40666 the lotacceptance inspection for the shipment and the results of the most recent periodic-check inspection.

There may be other requirements necessary to identify particular characteristics important to specialized applications. These may be specified by using the suffixes as given in Section 5.

  LIBRO TEORIA SOCIOLOGICA CLASICA GEORGE RITZER PDF

D – 01A Nylon Injection and Extrusion Materials_百度文库

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. This example is a general purpose, low viscosity nylon 6 material where U denotes?

This standard does not purport to address all of the safety concerns, if any, associated with its use. Inherent viscosity of Group 06 shall be measured on 0. It is recommended that the material manufacturer be consulted on all call-outs against this classi?

Inspection frequency shall be adequate to ensure the material is certi? NOTE 9—An example of this classi? For the zstm of the user, Committee D20 has highlighted those changes that may impact the use of this classi?

Q For general information not a requirement.

Nylon Processing and T Refer to Table X3. There may be other requirements necessary to identify particular characteristics important to specialized applications. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Details of these methods will be included in asym future revision of Speci? The lot-acceptance inspection shall consist of the tests listed as they apply: If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. It is recommended that the material manufacturer be consulted on all call-outs against this classification system.