Categories : Education

this manual may be trademarks or registered trademarks of their respective companies and are. View and Download Symbol LS quick start manual online. LS Scanner pdf manual download. Also for: Ds View and Download Motorola LSFZ product reference manual online . User Manual. LSFZ Barcode Reader pdf manual download.

Author: Kagami Doumuro
Country: Iran
Language: English (Spanish)
Genre: Sex
Published (Last): 2 September 2011
Pages: 329
PDF File Size: 10.71 Mb
ePub File Size: 12.58 Mb
ISBN: 332-3-19322-712-4
Downloads: 58119
Price: Free* [*Free Regsitration Required]
Uploader: Kagara

Page Code 3 of 9 Code All programmed rules are stored in a buffer. Page http: Reader has checked and stripped check character.


A dirty window can affect scanning accuracy. To enable or disable Trioptic Code 39, scan the appropriate lx3408 code below. Set the scanner’s baud rate to match the baud rate setting of the host, or data may not reach the host device or may reach it in distorted form.

Erase Advanced Data Formatting 14 – 7 Erase Use these bar codes to erase criteria, actions, or rules. Standard Default Parameters Appendix B: The second check digit is optional.

Throughout the programming bar code menus, asterisks indicate default values. If your keyboard type does not ls34088, see Alternate Numeric Keypad Emulation on page Page Programming Reference B – Discrete 2 Of 5 d 2 Of 5 Codes.

This specular reflection can make decoding difficult. Ls4308 part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. Selecting the host type sets the parameter defaults as listed in Table Keyboard Wedge Interface 5 – 7 Ignore Unknown Characters Unknown characters are characters the host does not recognize.

Page 60 5 – 12 Symbol LS Product Reference Guide if double key if double key Page The scanner de-asserts RTS when the transmission is complete. In addition to any single character prefix already selected, the Code ID character is inserted between the prefix and the decoded symbol. Ensure the scanner is properly connected to the host see the appropriate host chapter.


LS3408-ER Rugged Barcode Scanner Support

Send Data Send all data that remains, send all data up to a specific character selected from the Alphanumeric Keyboard on pageor send the next N characters. The following actions work for all send commands that follow it within a rule. There are three options for transmitting UPC-E preamble to the host device: Move Cursor Past a Specific This action moves the cursor past the first occurrence of a selected Symbologies 12 – 39 CLSI Editing When enabled, this parameter strips the start and stop characters and inserts a space after the first, fifth, and tenth characters of a character Codabar symbol.

Limited symbol encoding a single zero as the first digit, ls4308 report the bar code as EAN For example, to mahual bar code data without the UPC-A check digit, scan the Motorola recommends the default setting.

No Delay 0 msec Medium Delay 20 msec. Some decoders, however, do not assert the Decode signal to tell the scanner that a decode has occurred.

Code 11 Manuxl Digit Verification Code 11 Check Digit Verification Nanual feature allows the scanner to check the integrity of all Code 11 symbols to verify that the data complies with the specified check digit algorithm.

By default, a space replaces any characters that do not have a corresponding character in the Code 39 symbology set. The scanner and connected decoder both process the parameter. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright law.


Connecting Power if Required 1 – 4 Symbol LS Product Reference Guide Close the clamp, push it back into place and tighten the screws on the clamp to secure the cable into the bottom of the scanner.

Page NOTE Due ks3408 the construction of the D 2 of 5 symbology, it is possible for a scan line covering only a portion of the code to transmit as a complete scan, yielding less data than is encoded in the bar code. The options are to check for one check digit, check for two check digits, or disable the feature. The mznual codes must be read three times: Option Value Option Check digits are sent. All programmed rules are stored in a buffer.

To enable or disable EAN-8, scan the appropriate bar code below. With MSI symbols, one check digit is mandatory and always verified by the reader.


When enabled, the case of the data is preserved regardless of the state of the caps lock key. If the symbol does not have a supplemental, the scanner must decode the bar code the number of times set via Scan data can be edited to suit the particular requirements.

Rules Hierarchy in Bar Codes The order of programming individual rules is important.

When in reduced power mode, the scanner draws less current from its power source. Connect the other end of the Synapse Smart Cable to the host. Select one length per rule only.